Toyota Celica Installation Guide PPE Engineering 2ZZ-GE Race Header

PPE Engineering 2ZZ-GE Race Header for Toyota Celica/Matrix/Corolla:

Included in kit:
1 Header
1 Stainless Steel Flex section
1 Header flange
1 Header flange gasket
1 Set of flange hardware (bolts/nuts/washers)
1 Midpipe *optional

Header Installation:
1. Support body of vehicle. *Access to a vehicle lift make installation easier.
2. Remove stock midpipe.
a. Remove O2 sensors, bolts and hangers
3. Remove rear motor mount and motor mount bracket.
4. Support engine with jack.
5. Remove bolts holding in subframe….

Download PPE Engineering 2ZZ-GE Race Header for Toyota Celica/Matrix/Corolla Installation Guide.Pdf
 Download here

2003-2004 Toyota Matrix Intake Kit Installation Instructions Manual

Intake Kit Installation Instructions: ’03-’04 Toyota Matrix & Pontiac Vibe. Complete kit with parts. Step 1. With sensors disconnected, now remove upper Step 2. Disconnect wiring harnesses leading to Mass Airflow Sensor, VSV valves located to either side of MAS on factory airbox (indicated by arrows). On the brown harness toward the front end of the car, place provided rubber cap over harness lead. Step 3. From the throttle body, there is a _” vacuum line that extends into
check valve and then a “T” connection. Disconnect the smaller (bat-
tery side) vacuum tube from the check valve. Now disconnect longer
vacuum tube from “T” and reconnect to now open check valve. The
remaining “T” and hoses will be removed with the airbox…

Download Intake Kit Installation Instructions: ’03-’04 Toyota Matrix & Pontiac Vibe.Pdf
 Download here

Download Manual Carburetor Inspection Procedure Toyota Fuel System

The following instructions are organized so that you work on only one component group at a time. This will help avoid confusion from similar looking parts from different sub-assemblies being on your workbench at the same time. (a) To facilitate reassembly, arrange parts in order. (b) Be careful not to mix up or lose clips or springs. (c) Use carburetor driver set SST. Remove air cleaner support, remove throttle position switch, Remove fuel cut solenoid valve (a) Remove the two clamps. (b) Disconnect the solenoid valve and throttle position switch wire from the clamp. (c) Remove the solenoid valve and gasket. Remove nipple union and gaskets. Remove compensator. Remove the three screws, throttle position switch wire clamp, compensator and gasket. HINT: Remove the compensator only if it is necessary to replace it. Remove suction chamber adjusting pin. Remove suction chamber and piston. Remove pump arm. Remove float bowl : (a) Disconnect the fuel heater wire from the clamp. (b) Remove the five screws, union nipple clamp, throttle valve solenoid, wire clamp, washer, number plate, EGR vacuum modulator bracket and float bowl. (c) Remove the pump damping spring from float bowl…..

Download Manual Carburetor Inspection Procedure Toyota Fuel System.P
 Download here

Free Electrical Wiring Diagram Toyota Camry

INTRODUCTION A …. HOW TO USE THIS MANUAL B …. TROUBLESHOOTING C …. ABBREVIATIONS D …. GLOSSARY OF TERMS AND SYMBOLS E …. RELAY LOCATIONS F …. ELECTRICAL WIRING ROUTING G …. POWER SOURCE (Current Flow Chart) H…SYSTEM CIRCUITS ABS (ANTI-LOCK BRAKE SYSTEM) AIR CONDITIONER (PUSH CONTROL SW TYPE) AIR CONDITIONER (LEVER CONTROL SW TYPE) AUTO ANTENNA BACK-UP LIGHT CHARGING CIGARETTE LIGHTER AND CLOCK COMBINATION METER CRUISE CONTROL DOOR LOCK….GROUND POINTS J OVERALL ELECTRICAL WIRING DIAGRAM K….

Download Toyota Camry Electrical Wiring Diagram.Pdf
 Download here

MIL ON – DTC P1133 Updated (Oxygen Sensor Circuit) ENGINE EG004-01 April 20, 2001 Title: M.I.L. “ON” P1133 Models: ‘97 – ‘99 Camry and ‘99 Solara Introduction…Under certain driving conditions, some 1997 – 1999 5S-FE California emission specification Camrys
and 1999 5S-FE California emission specification Solaras may exhibit a M.I.L. “ON” with DTC P1133 (Air Fuel Ratio Sensor Slow Response Malfunction). An improved Air Fuel Ratio (A/F) Sensor was developed to correct this condition (See TSB EG006-99). In some rare cases, P1133 may still set after the improved A/F sensor is installed. The Engine Control Module (ECM) logic has been modified to correct this condition. Applicable Vehicles Top – Vehicle Technical Service Bulletins . Customer Interest . . MIL ON – DTC P1133 Updated (Oxygen Sensor Circuit) . Notes ^ 1997 – 1999 model year Camrys with 5S-FE California emission specification. ^ 1999 model year Solaras with 5S-FE California emission specification….

Download 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI.Pdf
 Download here

2006 Toyota CAMRY SOLARA ELECTRICAL WIRING DIAGRAM

CAMRY SOLARA (EWD628U)
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . A . . . . 2
HOW TO USE THIS MANUAL . . . . . . . . . . . . . . . B . . . . 3
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . C . . . . 12
ABBREVIATIONS . . . . . . . . . . . . . . . . . . . . . . . . . D . . . . 17
GLOSSARY OF TERMS AND SYMBOLS . . . . . E . . . . 18
RELAY LOCATIONS . . . . . . . . . . . . . . . . . . . . . . . F . . . . 20
ELECTRICAL WIRING ROUTING . . . . . . . . . . . G . . . . 40
SYSTEM CIRCUITS . . . . . . . . . . . . . . . . . . . . . . . . H . . . . 62
GROUND POINT . . . . . . . . . . . . . . . . . . . . . . . . . . . I . . . . 292
POWER SOURCE (Current Flow Chart) . . . . . J . . . . 302
CONNECTOR LIST . . . . . . . . . . . . . . . . . . . . . . . . K . . . . 310
PART NUMBER OF CONNECTORS . . . . . . . . . L . . . . 324
OVERALL ELECTRICAL WIRING DIAGRAM . M . . . . 328

This manual provides information on the electrical circuits installed on vehicles by dividing them into a circuit for each system. The actual wiring of each system circuit is shown from the point where the power
source is received from the battery as far as each ground point. (All circuit diagrams are shown with the switches in the OFF position.)
When troubleshooting any problem, first understand the operation of the circuit where the problem was detected (see System Circuit section), the power source supplying power to that circuit (see Power Source section), and the ground points (see Ground Point section). See the System Outline to understand the circuit operation. When the circuit operation is understood, begin troubleshooting of the problem
circuit to isolate the cause. Use Relay Location and Electrical Wiring Routing sections to find each part, junction block and wiring harness connectors, wiring harness and wiring harness connectors and ground points of each system circuit. Internal wiring for each junction block is also provided for better understanding of connection within a junction block….

Download 2006 CAMRY SOLARA ELECTRICAL WIRING DIAGRAM.Pdf
 Download here

1986 Toyota Corolla (RWD WIRING DIAGRAM SYMBOLS

HOW TO USE THE WIRING DIAGRAMS 1) On the first page of the diagram, you will find a listing of major electrical components or systems. Locate the specific component or system you wish to trace. A grid number and letter will follow the component’s name. 2) Use the grid NUMBERS (arranged horizontally across the top and bottom of each page) to find the page of the wiring diagram that contains the component you’re seeking. When you reach this page, use the grid LETTERS on the side of the page to determine the component’s vertical location. 3) Locate the circuit you need to service. The internals are shown for switches and relays to assist you in understanding how….

circuit operates. NOTE: In some of the newer wiring diagram articles in this product, there is a Legend for the wiring diagrams that has been created to make locating components easier. For these articles, there will be a COMPONENT LOCATION MENU title in the article main menu. These articles will also have the original legend available on the first graphic…..

Download WIRING DIAGRAM SYMBOLS 1986 Toyota Corolla (RWD).Pdf
 Download here

1993 Toyota MR2 Article Text manuals

M – VACUUM DIAGRAMS Article Text 1993 Toyota MR2…For Ace Mechanics 123 Main Street San Diego Ca 92126 Copyright © 1997 Mitchell International Friday, November 28, 2003 11:59AM ARTICLE BEGINNING 1993 ENGINE PERFORMANCE Vacuum Diagrams Camry, Celica, Corolla, Land Cruiser, MR2, Paseo, Pickup, Previa, Supra, Tercel, T100, 4Runner INTRODUCTION This article contains underhood views or schematics of vacuum hose routing. Use these vacuum diagrams during the visual inspection in the appropriate F – BASIC TESTING article. This will assist in identifying improperly routed vacuum hoses which cause driveability and/or computer-indicated malfunctions. VACUUM DIAGRAMS CAMRY … Fig. 3: Vacuum Diagram (Celica 1.6L 4A-FE) Courtesy of Toyota Motor Sales, U.S.A., Inc….

Download M – VACUUM DIAGRAMS Article Text 1993 Toyota MR2.Pdf
 Download here

Toyota Wiring Diagram

Using the Electrical wiring diagram, One of the key to a quick and successful electrical diagnosis is correctly using the Toyota Electrical Wiring Diagram or EWD. EWD is not just a book of wiring diagrams, but an information resource for anything electrical on the vehicle. Everything from connector ID and location to what circuits share splice points is included in this manual. Because there is so much information, it takes a little practice to learn where is located, and what each of EWD symbols and individual sections can tell you. We will take a detailed look at all of these features and how to use them in diagnosing an electrical problem…

There are two table of contents that are available. One is on the title page of the book. This list all of sections (A-K) and the also has alphabetical list of all the system circuit diagrams located in section I. These wiring diagrams are the “heart” of the EWD, and the place to start when diagnosis an electrical problem. There is also a listing of each system circuit diagram on the fist page of section I. 1993 Toyota Camry Electrical wiring diagram…..

Download Using Toyota Wiring Diagram.Pdf
Get the file  Download here

Download TOYOTA PRADO GXL 4.0 litre V6 automatic Manuals

Toyota has pinned its hopes on reclaiming the number one position in the mid-size four wheel drive segment with an all-new Toyota Prado range of off-road wagons. The second generation Prado is still a five door, eight seat configuration that uses a separate chassis. This formula has been a successful one for Toyota, having been used on the first Prado that was launched in 1996. While the basic layout of the original Prado remains, the new models are physically larger vehicles that feature more interior space. Other changes include a significantly more powerful V6 petrol engine option….

TECHNICAL SPECIFICATIONS ENGINE Type……………………… V6, DOHC, 24 valves Capacity in litres……………………………. 3.995 Induction ……………. Multipoint fuel injection Fuel recommendation……………………… ULP Claimed max. power…. 179 kW at 5200 rpm Claimed max. torque…. 376 Nm at 3800 rpm Specific power output…………..44.8 kW/litre TRANSMISSION Type………………………. Four speed automatic Driving wheels…..Constantfour wheel drive Speed per 1000 rpm in top gear….53.1 km/h WHEELS …………………….. Alloy, 7.5JJ x 17 Tyres…………………………………… 265/65 R17 Spare……………………………………….. Full size STEERING Type…………. Power assisted rack and pinion Turns lock to lock……………………………… 3.1 Turning circle (measured)………. 11.8 metres DIMENSIONS Mass…………………………………………. 2110 kg Length…………………………………….. 4850 mm Width (incl. mirrors 2120 mm) …… 1875 mm Height…………………………………….. 1865 mm Ground clearance (measured) ……….220 mm Seating capacity…………………………………… 8 Fuel tank capacity…………………….. 180 litres….

Download TOYOTA PRADO GXL 4.0 litre V6 automatic.Pdf
 Download here

1996 Toyota Tercel Repair Manual

This Toyota Tercel 1996 Repair Manual contains step-by-step repair procedures for engine overhaul, chassis electrical, drive train, suspension, steering and more. Most repair operations begin with an overview illustration identifying the components and showing how the parts fit together. The procedures are presented in a step-by-step format containing detailed specifications, exploded views and photographs, features expanded index to quickly locate information, Toyota tercel wiring diagrams, diagnostic and troubleshooting charts, and glossary to identify unfamiliar terms…..
Download Toyota Tercel 1996 Repair Manual.Pdf
 Download here

Download [PDF] Haynes Manual for Toyota Land Cruiser

automotive manuals Haynes also has the best ATV repair and maintenance information available on the market 10450 565 2553 2125 2318 2465 2351 2302 2508 1154 2317 2217 2126 2314 2567 ATV Basics Manual Honda ATC70 90 110 185 200 71 thru 82 Honda TRX250 TRX250EX TRX350 ATVs 97 thru 05 Honda TRX300 Shaft Drive 88 thru 00 Honda TRX300EX TRX400EX ATVs 93 thru 06 Honda Foreman 400 450 and Rubicon ATVs 95 thru 07 Updated Kawasaki Bayou Prairie ATVs 86 thru 03 Polaris ATVs 85 thru 97 Polaris ATVs all gasoline PVT models 98 thru 06 Yamaha ATVs 80 thru 85 Yamaha YFS 200 Blaster 88 thru 06 Updated Yamaha 250 Timberwolf 92 thru 00 Yamaha YFM350 Big Bear and ER 87 thru 03 Yamaha Banshee and Warrior ATVs 87 thru 03 Yamaha Kodiak and Grizzly ATVs 93 thru 05 VOLVO VOLVO 120 Series 130 Series 140 Series 220 Wagon 240 Series 740 Series 760 Series 850 Series P1800 Sports 61 73 61 73 66 74 61 73 76 93 82 88 82 88 93 97 61 73 97010 97010 97015 97010 97020 97040 97040 97050 97010 The worldwide leader in automotive repair information for close to 50 years 17 New titles coming soon 24047 43050 72011 72032 Chevrolet Impala Monte Carlo 2006 thru 2008 Hyundai Santa Fe 2001 thru 2006 Nissan 350Z Infinity G35 2003 thru 2007 Nissan Frontier Xterra 2005 thru 2007 Haynes New titles and updates now available 10333 24010 24027 24066 24072 25027 25040 30022 30023 36012 36025 36051 36052 36060 38017 38027 42037 87011 89100 92078 92081 92082 96009 Engine Performance Techbook Chevrolet Astro GMC Safari 1985 thru 2005 Chevrolet Colorado GMC Canyon 2004 thru 2006 Chevrolet Silverado GMC Sierra 1999 thru 2006 Chevrolet TrailBlazer GMC Envoy 2002 thru 2006 Chrysler 300 Dodge Charger Magnum 2005 thru 2007 Chrysler Sebring Dodge Stratus Avenger 1995 thru 2005 Dodge Durango 2000 thru 2003 Dakota 2000….

Download Toyota Land Cruiser Haynes Manual.Pdf
 Download here

5 Speed Transmission Electronic Speedo Drive for Toyota T50

T50 Speedo Drive Adaption Rev 1 Feb 2003 1 Electronic Speedo Drive for Toyota T50 5 Speed Transmission Speedo drive conversion to adapt Toyota AE101 electronic drive to AE86 … Step One:- Dissassembly T50 Drive:- Disassembly is simple, remove the “C” clip from the drive housing , just above the drive gear. This will allow the shaft/gear assembly to be withdrawn from the housing. Remove the “O” ring from the housing. Wash all parts internally and externally to remove oil, grease and road grime …… AE101 Drive:- Disassembly is similar to T50, remove the “C” clip from the drive housing , just above the drive gear. This will allow theshaft /gear assembly to be withdrawn from the housing. Remove the “O” rings from the housing. Remove the three (3) philips head screws from the cover on the top of the drive housing. Carefully remove cover, be aware that the small parts in side may be stuck to the cover. Remove all internal parts, record order of assembly. Wash housing andshaft to remove oil, grease and road grime….

Download Electronic Speedo Drive for Toyota T50 5 Speed Transmission.Pdf
 Download here

Free SYSTEM WIRING DIAGRAMS for1995 Toyota MR2

SYSTEM WIRING DIAGRAMS Article Text 1995 Toyota MR2 For Rse 555 Main Street Clarksville Va 22901 Copyright © 1997 Mitchell International Thursday, February 14, 2002 04:10PM ARTICLE BEGINNING 1995 System Wiring Diagrams Toyota – MR2 AIR CONDITIONING Air Conditioning Circuits (1 of 2) SYSTEM WIRING DIAGRAMS Article Text (p. 2) 1995 Toyota MR2For Rse 555 Main Street Clarksville Va 22901 Air Conditioning Circuits (2 of 2) ANTI-LOCK BRAKES SYSTEM WIRING DIAGRAMS Article Text (p. 3) 1995 Toyota MR2For Rse 555 Main Street Clarksville Va 22901 Anti-lock Brake Circuits ANTI-THEFT SYSTEM WIRING DIAGRAMS Article Text (p. 4) 1995 Toyota MR2For Rse 555 Main Street Clarksville Va 22901 Anti-theft Circuit COMPUTER DATA LINES 2.0L
SYSTEM WIRING DIAGRAMS Article Text (p. 5) 1995 Toyota MR2For Rse 555 Main Street Clarksville Va 22901 2.0L Turbo, Computer Data Lines 2.2L SYSTEM WIRING DIAGRAMS Article Text (p. 6) 1995 Toyota MR2For Rse 555 Main Street Clarksville Va 22901 2.2L, Computer Data Lines SYSTEM WIRING DIAGRAMSArticle Text (p. 7) 1995 Toyota MR2For Rse 555 Main Street Clarksville Va 22901 COOLING FAN Cooling Fan Circuit SYSTEM WIRING DIAGRAMS Article Text (p. 8) 1995 Toyota MR2For Rse 555 Main Street Clarksville Va 22901 CRUISE CONTROL Cruise Control Circuit DEFOGGERS SYSTEM WIRING DIAGRAMS Article Text (p. 9 ) 1995 Toyota MR2 For Rse 555 Main Street Clarksville Va 22901 Defogger Circuit SYSTEM WIRING DIAGRAMS Article Text (p. 10) 1995 Toyota MR2For Rse 555 Main Street Clarksville Va 22901 ELECTRONIC POWER STEERING Electronic Power Steering…

Download 1995 Toyota MR2 SYSTEM WIRING DIAGRAMS.Pdf
 Download here

Manual books for 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI

Automatic Equipment Mfg. Co. One Mill Road, Industrial Park l Pender, Nebraska 68047 BX3716 Installation Instructions 1987-91 Toyota Camry Installation of this baseplate requires …

Installation of this baseplate requires removing the vehicle’s tie down brackets. On 1991 models, the lower metal bumper/spoiler will need to be removed. 1. Read the General Instruction Sheet included with this baseplate. 2. The baseplate mounts to the front of the car using ten bolts (eight existing and two supplied): five on each side of the car. 3. Remove the ìtie downî bracket from each side of the car and inspect the bolts for reuse. These brackets are stamped sheet metal with an oval hole facing downward. 4. Remove the front bolt ONLY from the two sway bar brackets. These bolts will not be reused. 5. Remove the two bolts (one on each side) located just above the front trim panel which hold the bumper brackets to the car and inspect for reuse. 6. Position a side bracket such that its hole align with the ìtie downî and sway bar bracket holes. Hand start the previously removed tie down bracket bolts and a new sway bar bracket bolt with a lockwasher. Use locktite on all bolts but do not tighten yet. 7. Repeat with other side of the bracket. 8. Position the baseplate between the side brackets aligning with the side plate holes and the bumper bracket holes. Hand start the previously removed bumper bracket holes and attach the side brackets with 1/2″ bolts, nuts, and lock washers supplied. 9. When all bolts align, tighten securely. 10. The dimensional variations between otherwise identical cars can be considerable. While the location and size of the holes in the baseplate were designed to facilitate easy installation, it may be necessary to file a hole slightly to allow a bolt to clear. 11. Install the tow bar and safety cables according to the instructions included in their packages. 12. Do not substitute other devices if the pin and clip are lost. 13. DEALER OR INSTALLER: BE CERTAIN THE USER RECEIVES THE INSTRUCTION SHEET. 14.1991 Model – The baseplate will fit the 1991 Camry, however, lower metal bumper/spoiler will need to be removed while base plate is installed…

Download 1998 Toyota Camry CE Sedan L4-2164cc 2.2L DOHC MFI.Pdf
 Download here

Free Download CHILD RESTRAINT SEAT TOP STRAP BRACKET INSTALLATION Camry 83 – 00 All Models Technical Service BULLETIN

Owner’s Manual Installation Reference … TOP STRAP BRACKET INSTALLATION – BO010-02 May 24, 2002 Page 4 of 9 OWNER’S MANUAL 4Runner Avalon Camry Sedan Camry Liftback Camry Solara Camry Wagon Celica …

Child restraint seat top strap bracket installation procedures are provided to supplement the Owner’s Manual. Beginning with 2001 models, the top strap brackets are factory installed. The child restraint seat top strap assembly is not available as a service part. Contact the child restraint seat manufacturer for recommended top strap information, top strap to child restraint seatinstallation instructions, and top strap retailers. The top strap brackets can only be installed on vehicles that have nuts welded in place by the factory. The locations of these nuts can be found in the Owner’s Manual (for most 1983 and newer models.) Toyota does not recommend modifying vehicles that do not have nuts welded in place by the factory. Some Land Cruiser and RAV4 vehicles, prior to 2001 model year, may not have these nuts welded in by the factory…. CHILD RESTRAINT SEAT TOP STRAP BRACKET INSTALLATION – BO010-02 May 24, 2002 Page 2 of 9 Child Restraint Seat Top Strap Bracket Installation Obtain the exact year and vehicle model Toyota Owner’s Manual before beginning installation. 1. Confirm with the customer which seat location(s) they will be installing the child restraint seat. The Owner’s Manual seat section provides an illustration showing available top strap bracket location(s). The illustration page in the Owner’s Manual is provided in pages 4-9 of this bulletin. NOTE: Determine which kit parts are needed for each specific child seat location, by referring to pages 4-9 of this bulletin. 2. Remove a 20 mm diameter area of the carpet or trim material above the bracket mounting location. In some vehicles, a 20 mm circle is already pre-cut into the interior trim material. Once the interior trim material is removed, the nuts welded in by the factory should be visible. 3. If a 5 mm or 15 mm spacer is specified, remove the red lock washer from the Bracket Sub-Assembly (P/N 73709-12010) and remove the 10 mm spacer. Assure the red lock washer is re-installed onto the bolt. If a 5 mm spacer is needed, use the 15 mm bolt from the CRS Kit (P/N 04731-22012). Installation Procedure Bolt Spacer 100 mm (4.0 in.) Anchor Bracket 185 mm (7.3 in.) 345 mm (13.6 in.) Example of 1999 Camry Showing Three (3) Available Bracket Locations…
Download CHILD RESTRAINT SEAT TOP STRAP BRACKET INSTALLATION Camry 83 – 00 All Models Technical Service BULLETIN.Pdf
 Download here

1997-2001 Toyota Camry 1999-2003 Toyota Solara Installation Manual TWM Performance Short Shift Kit

Installation Manual TWM Performance Short Shift Kit 1997-2001 Toyota Camry 1999-2003 Toyota Solara 1. Unscrew the shift knob and remove the boot. 2. 3. Unplug the lighter assembly from the bottom of the cover you just popped out. 4. Remove the 2 screws at the front of the console. 5. Remove the plastic cover in front of the handbrake. 6. Remove the rubber mat, and the two bolts in the storage compartment of the center console. 7. Unclip the plastic connector at the front of the console. 8. Carefully lift and remove the console from the car to allow access to the shift assembly. 9. Remove the clip on the left side of the assembly. 11. Insert a flat head screw driver behind the clip on the right front side of the assembly and pry the clip off. The clip may be broken in the process but a new one is included with the TWM shifter. 12. Use a punch to drive out the pin and remove the plastic side arm. Note the position of the spring before removal of the arm….
Download Installation Manual TWM Performance Short Shift Kit 1997-2001 Toyota Camry 1999-2003 Toyota Solara.Pdf
 Download here

Free Park Brake Bellcrank Repair Guide for Toyota Truck

Toyota trucks including Tacoma, T100 and Tundra with rear drum brakes use a bellcrank apparatus through the brake backing plate as part of the parking brake system. These bellcranks, made of aluminum and steel are known for seizing up…..

The sagging cable that runs across the differential is a warning. If you notice this you need to check the action of the bellcranks before using theparking brake further. Using the parking brake with this condition can cause damage to the brake shoes and drum. You can check the action of the bellcrank manually to verify the bellcrank is seized. It should move freely. Even if the cable is just too tight you should be able to pull the cable towards the side that is not against the backing plate, while pulling the other side off. If you find you can get no movement from the bellcrank, its time to pull the drums and get to work. RemovingToyota Drums If you have never removed your drums, you will likely find that they are stuck in place. Rust tends to build up between the drum and hub flange making them difficult to remove. Here are some tips for removing the drum as shown in figure 3. Using sandpaper, remove as much rust as possible on the flange that is exposed on the out side of the drum. Soak the drum at the hub with penetrating oil. Be sure to spray some in the holes between the studs. Removing the Bellcrank: Once the drum has been removed inspect the brake shoes for wear and cracking of the shoe material from excessive heat. If this is found, the shoes should be replaced. If heat damage is found on the shoes, inspect the brake drum surface for scoring or hot spots. If this is found the drum may need replaced also.
Download Toyota Truck Park Brake Bellcrank Repair Guide.Pdf
 Download here

Free 2003 Toyota 4Runner Repair manuals

2003 4R UNNER University of Toyota Jul. 17, 02 p. 28 of 33 SR5_mud VSC_ Trac E. VSC & TRAC … the URL ftp://press:2003 Toyota@ftp2.maritz.com and select the 4Runner … 2003 4R UNNERUniversity of Toyota Jul. 17, 02 p. 2 of 33 C:\DataFiles\03_4Runner\Presentations\03_4Runner_LLPP_v7a.doc I. 2003 4RUNNER….. 4 A. 4 th generation of the 4Runner…..

I. 2003 4RUNNER A. 4th generation of the 4Runner 1. continues it’s legacy of mid-SUV class-leader in: a. on-road comfort, b. all-weather safety, and c. off-road capability 2. all-new model for US, Japan, & export markets a. new model related to the Land Cruiser Prado, a 7/8-size Land Cruiser not previously offered in US b. severs the connection to the Tacoma truck line 3. mid-SUV class continues to grow in the US: a. this class of vehicles offers a good view of the road, b. easy ingress/egress, c. roomy passenger space, d. large payload and towing capacities, e. on-road comfort & handling, f. go-anywhere off-road capabilities. profile_dimensions.jpg Cross_Section 4. new 4Runner is larger in many key dimensions: a. overall length > 4½” to 187.8″ b. wheelbase > 4½” 109.8″ c. ft leg room > 2″ 44″ d. rr leg room > 1½” 38¼” e. headroom > ½” 39.7″ ft / 39.1″ rr f. pass-pass width > 2″ 30″ g. shoulder room > 4½” / 4″ 58″ ft / 57.2″ rr h. hip room > 5½” / 4″ 55.3″ ft & rr i. track > 2½” 62″ j. overall width > 3″ 73.8″…
Download 2003 Toyota 4Runner.Pdf
 Download here

2007 Toyota Camry INSTALLATION INSTRUCTIONS manuals

INSTALLATION INSTRUCTIONS TO START: 1. Turn the ignition OFF and disconnect the vehicle’s negative battery cable. 2. Disconnect the mass air sensor electrical connection and release the wiring harness from the air box lid.
Tools: 3. Loosen the stock intake tube hose clamp and two upper air box mounting bolts as shown in the photograph. 4. Remove the air box lid from thevehicle. 5. Remove the two bolts that secure the fresh air intake to the radiator core support. Note: These bolts will be re-used, do not discard. Flat Blade Screwdriver, Phillips Screwdriver, Ratchet, Extension, 10mm Socket, Pliers, 10mm Wrench, 17mm Wrench, 3mm Allen Wrench, 4mm Allen Wrench. Description Qty. Part # 7. Remove the three bolts that secure the lower air box to the mounting bracket. 6. Remove the fresh air intake from the lower air box; then, remove from thevehicle. 8. Remove the lower air box from the vehicle as shown in the photograph. 9. Remove the two bolts that secure the lower air box mounting bracket to the inner fender and set aside; then, remove the mounting bracket from thevehicle. 10. Remove the two nuts that secure the engine cover; then, remove the engine cover from the vehicle and set aside. Note: Engine cover nuts will be re- used, do not discard. NOTE: FAILURE TO FOLLOW INSTALLATION INSTRUCTIONS AND NOT USING THE PROVIDED HARDWARE MAY DAMAGE THE INTAKE TUBE, THROTTLE BODY AND ENGINE….

Download 69-8610 INSTALLATION INSTRUCTIONS Toyota 2007 Camry I4-2.4L.Pdf
 Download here